To prevent any confusion, I change the name of my wifi dongle which I am going to use for my access point to wap0

The Raspberry Pi can be used as a wireless access point, running a standalone network. This can be done using the inbuilt wireless features of the Raspberry Pi 3 or Raspberry Pi Zero W, or by using a suitable USB wireless dongle that supports access points.

Note that this documentation was tested on a Raspberry Pi 3, and it is possible that some USB dongles may need slight changes to their settings. If you are having trouble with a USB wireless dongle, please check the forums.

To add a Raspberry Pi-based access point to an existing network, see this section.

In order to work as an access point, the Raspberry Pi will need to have access point software installed, along with DHCP server software to provide connecting devices with a network address. Ensure that your Raspberry Pi is using an up-to-date version of Raspbian (dated 2017 or later).

Use the following to update your Raspbian installation:

sudo apt-get update
sudo apt-get upgrade

Install all the required software in one go with this command:

sudo apt-get install dnsmasq hostapd

Since the configuration files are not ready yet, turn the new software off as follows:

sudo systemctl stop dnsmasq
sudo systemctl stop hostapd

Configuring a static IP

We are configuring a standalone network to act as a server, so the Raspberry Pi needs to have a static IP address assigned to the wireless port. This documentation assumes that we are using the standard 192.168.x.x IP addresses for our wireless network, so we will assign the server the IP address 192.168.4.1. It is also assumed that the wireless device being used is wlan0.

To configure the static IP address, edit the dhcpcd configuration file with:

sudo nano /etc/dhcpcd.conf

Go to the end of the file and edit it so that it looks like the following:

interface wlan0
    static ip_address=192.168.4.1/24
    nohook wpa_supplicant

Now restart the dhcpcd daemon and set up the new wlan0 configuration:

sudo service dhcpcd restart

Configuring the DHCP server (dnsmasq)

The DHCP service is provided by dnsmasq. By default, the configuration file contains a lot of information that is not needed, and it is easier to start from scratch. Rename this configuration file, and edit a new one:

sudo mv /etc/dnsmasq.conf /etc/dnsmasq.conf.orig  
sudo nano /etc/dnsmasq.conf

Type or copy the following information into the dnsmasq configuration file and save it:

interface=wlan0      # Use the require wireless interface - usually wlan0
  dhcp-range=192.168.4.2,192.168.4.20,255.255.255.0,24h

So for wlan0, we are going to provide IP addresses between 192.168.4.2 and 192.168.4.20, with a lease time of 24 hours. If you are providing DHCP services for other network devices (e.g. eth0), you could add more sections with the appropriate interface header, with the range of addresses you intend to provide to that interface.

There are many more options for dnsmasq; see the dnsmasq documentation for more details.

Configuring the access point host software (hostapd)

You need to edit the hostapd configuration file, located at /etc/hostapd/hostapd.conf, to add the various parameters for your wireless network. After initial install, this will be a new/empty file.

sudo nano /etc/hostapd/hostapd.conf

Add the information below to the configuration file. This configuration assumes we are using channel 7, with a network name of NameOfNetwork, and a password AardvarkBadgerHedgehog. Note that the name and password should not have quotes around them. The passphrase should be between 8 and 64 characters in length.

interface=wlan0
driver=nl80211
ssid=NameOfNetwork
hw_mode=g
channel=7
wmm_enabled=0
macaddr_acl=0
auth_algs=1
ignore_broadcast_ssid=0
wpa=2
wpa_passphrase=AardvarkBadgerHedgehog
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP

We now need to tell the system where to find this configuration file.

sudo nano /etc/default/hostapd

Find the line with #DAEMON_CONF, and replace it with this:

DAEMON_CONF="/etc/hostapd/hostapd.conf"

Start it up

Now start up the remaining services:

sudo systemctl start hostapd
sudo systemctl start dnsmasq

I have noticed on several occasions that after starting hostapd, that the ssh seams to crash/becomes unresponsive, this maybe be a result of the change in the network. If this happens, unplug, give it a few seconds, then plug your RPI back in. if you didnt cut and paste both commands, you will need to do the last command sudo systemctl start dnsmasq when your RPI comes online



Reboot